این برد کم هزینه است و حداقل سیستم توسعه برای ARM STM32F103C8T6 میباشد.
ARM CORTEX M3 با هسته 32 بایتی و STM32برد برای افرادی مناسب است که میخواهند میکروکنترلرهای
یاد بگیرند.
ویژگی ها
· دارای رابط مینی USB روی برد، میتوان به برد منبع تغذیه و ارتباطات USB را داد.
· نشانگر تست LED روی برد
· دکمه تنظیم مجدد و نشانگر LEDقدرت رو برد
· تنظیم کننده 100ma 3.3v روی برد
· همه GPIO ها خارجی هستند و اسم همه ی PIN ها مشخص است
· بعد ار اصلاح و بهبود هدر ها میتوان برد را بطور مستقیم ب برد مدار وصل کرد
مشخصات فنی
· شماره قسمت پردازنده(CPU):STM32F103C8T6
· هسته:ARM 32 CORTEX-M3 CPU
· حالت دیباگ:SWD (میتواند برنامه ریزی شود با ST-LINK V2
· ماکسیمم فرکانس کاری: 72 MGHZ
· منبع ولتاژ خارجی: 8MGHZ کریستال
· 64K فلش مموری، 20K SRAM
· 2.0 -0.3 Vمنبع تغذیه
· ریست (POR\PDR)
· سایز:5.3CM*2.2CM
Description
This board is low cost Minimum System Development Board for ARM Microcontroller – STM32F103C8T6. Board is suitable for learners that want to learn STM32 microcontroller with ARM Coretex-M3 32-bit core.
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
- Reset(POR/PDR)
- Size:5.3cm x 2.2cm
Documents and Downloads
- STM32F103C Datasheet
- Link to Arduino IDE and Libraries for STM32 project.
- STM32 and STM8 Flash loader demonstrator
- Link to How to program STM32F1 device using STM Flash loader demonstrator
Programming Instructions Using STM Flash Loader
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Package Includes
- 1x STM32 ARM Minimum System Development Board – STM32F103C8T6
- 1x 40 Pin header array